Weight capacity: 500 lb.
Hospital quality suitable for frequent, everyday use
Weight capacity: 500 lb.
100% Satisfaction Guarantee
At Cardinal Health, we stand behind our products with a 100% satisfaction guarantee. If for any reason you are not satisfied with your purchase, contact the healthcare provider or retailer where it was obtained for a replacement or refund. You can also contact us directly at 1-877-227-3462.
Wipe metal parts with a clean, soft cloth at least once a week. All metal parts can be cleaned with auto wax or similar products. If exposed to moisture, dry immediately. Do not use an abrasive cleanser that will scratch the finish. Use only a clean towel dampened with cool water when cleaning hand grips. Confirm that the grips are dry before using. NEVER use ammonia-based cleaning solutions or soap on hand grips, which may cause them to loosen or crack.
Large rear wheels should be inspected at least once a month to ensure proper tightness. If wheel wobbles or is loose, release lock nut and tighten axle bolt slightly. Test for proper tightness and alignment by leaning chair to one side and spinning adjusted wheel.
Tires need minimal maintenance, but should be cleaned as needed with a damp cloth. Replace if tires become worn or cracking appears.
Check casters and lubricate as needed. Lubricate by removing fork and greasing caster stem bearings with high-quality multi-purpose grease. Lubricate wheel bearings by removing wheel from fork. Reassemble fork and wheel by tightening lock nuts until no play remains, but wheels roll freely. If lock nut is too loose, caster will shimmy. If it is too tight, chair will be difficult to steer.
Do not attempt to adjust or operate your wheelchair without reading all instructions carefully. Failure to follow instructions may result in injury.
Consult with your healthcare provider if:
Do not exceed the maximum weight capacity or serious injury may result.
This chair does not conform to applicable standards for automobile seating and should not be used as a seat in a motor vehicle.
Do not operate this chair on roadways, streets, or any surfaces with vehicular traffic.
Do not attempt to operate on inclines 10° or greater without proper assistance.
Be sure to completely engage both wheel locks before getting in or out of chair, leaning forward in chair, or while in an elevator or wheelchair lift.
Chair should be on a smooth, stable, and level area with wheel locks engaged before transferring user in or out of chair.
Do not adjust footrests any lower than 2 ½ inches from the ground.
When getting in or out of chair, do not stand on or apply weight to footrests.
Before reaching or leaning forward, point front casters in a forward position and engage wheel locks to help prevent chair from tipping over.
Do not lean over or apply weight on the top of chair back, which can cause chair to tip over. When trying to extend arms over back, only reach as far as your arm can extend without having to alter your seating position.
DO NOT stand on chair.
DO NOT use wheel locks to slow your descent down an incline.
Abruptly changing directions while going down an incline could cause instability or possible tipping over.
At regular intervals, check and tighten all fasteners and hinged parts. Frequently check all plastic parts for wear. If any component of this product is damaged or missing, discontinue use immediately. Contact Cardinal Health at 1-877-227-3462 for repair and/or appropriate replacement parts. DO NOT use non-Cardinal HealthTM parts.
Use Cardinal HealthTM accessories only. The use of other manufacturers' accessories can result in an improper fit and risk of fall and/or injury.
Failure to follow the above instructions may result in serious injury and/or damage to the product. Cardinal Health assumes no responsibility for any injury or damage caused by improper installation, assembly, or use of this product.
Adjusting Your Wheelchair
To Open Chair
Open chair by tilting to one side and pushing down on seat rail until fully opened.
To Close/Fold Chair
To fold chair, pull up on the locks simultaneously, and carefully fold down the back support. Place foot plates in a vertical position. Grab seat with both hands at front and back edges, then lift. Or, tilt chair to one side and lift up on seat rail.
Adjusting Height of Foot Plates
Sit in chair with your feet on the foot plates. Using a hex wrench, loosen the bolt on the clamp around the support assembly. Raise or lower foot plate to a position that provides the most support of your thighs, then re-tighten bolt. Front rigging should not be so low that it causes uncomfortable pressure to thighs at front of seat upholstery. Footrest should not be lower than 2½ inches from the ground to ensure proper clearance.
Elevating/Lowering Leg Rests
Sit in chair with your feet on the foot plates. The individual assisting you should hold on to the leg rest support tube to raise the leg rest until the desired position is reached. To lower the leg rest, the individual assisting you should support the leg rest with one hand while pushing the release lever, then slowly lower the leg rest to the desired position.
Removal of Arms
Remove arms by depressing push buttons and lifting arms out of front and rear sockets.
Removal of Footrests
Release lock by pushing on the front rigging lever. Swing footrest out and sideways, then lift to remove.
Removal of Leg Rests
Release lock by pushing on the front rigging lever. Swing leg rest out and sideways, then lift to remove.
|CW0007CELR||Chrome||Elevating Leg Rests||32.68 in||46.46 in||36.61 in||62 lb|
|CW0007CSR||Chrome||Swing-Away Footrests||32.68 in||46.46 in||36.61 in||61 lb|
|CW0007PELR||Charcoal||Elevating Leg Rests||32.68 in||46.46 in||36.61 in||62 lb|
|CW0007PSR||Charcoal||Swing-Away Footrests||32.68 in||46.46 in||36.61 in||61 lb|
Using Your Wheelchair
Engage both wheel locks before getting in or out of chair, leaning forward in chair, or while in an elevator or wheelchair lift. Proper adjustment of wheel lock is at least 1/8 inch when locked. Locks are engaged by pushing handles completely forward. Adjustments to locks are made by loosening or tightening nut on the carriage bolt. Embed lock shoe at least 1/8 inch by sliding clamp toward rear wheel while handle is engaged in locked position. Tighten nut and bolt to secure in position. Test for correct locking action before actual use.
Wheelchair is designed to be stable as long as the center of gravity is maintained while going about normal activities. Care must be taken while performing activities that shift your center of gravity while in the chair. Never reach so far that you have to shift in the seat or lean out of the chair. When you have to reach for objects that require you to lean, be certain front casters are pointing in a forward position and wheel locks are engaged, which stabilizes the chair.
Be sure of your own capabilities, limitations, and strength before attempting to go up or down a ramp. Correct techniques on ramp negotiation should be shown to you by a healthcare provider. Assistance is recommended when going up or down inclines greater than 10˚. If you must stop on an incline, avoid sudden, abrupt movement when you resume movement. Because of backward angle of the chair, sudden abrupt movement could cause instability. Attempting to use the wheel lock brakes could result in accidental locking or tipping to one side or could cause a sudden stop. Avoid changing direction when going down an incline, as this could result in instability or tipping over